businesssuccesstrainingcp.blogspot.com How to repair a minor ding using a stud nail gun.
Share and Enjoy:
This entry was posted
on Friday, April 2nd, 2010 at 8:45 pm and is filed under Dent.
You can follow any responses to this entry through the RSS 2.0 feed.
You can skip to the end and leave a response. Pinging is currently not allowed.
10 Responses to “Dent Repair Using a Weld-on Stud Nail Gun”
What you mean by high area? the t pull is to pull the dent out right? is the high area visible which is why you are hammering it. High are an in a bump facing outward of the damage area?
A common mistake is to just work on the direct (low) damage and not the high areas. It is important to work on both areas at the same time. You want to push in on your highs as you pull out on your lows. This will allow the metal to return to it’s origional shape with out forcing or streching the metal.
i do prefer to pull the trigger on the spot welder for only about 1/2 second. the studs to pop off every now and then, but this helps when pulling them off. just a little jiggle and they are off “no hole no grinding no cutting”. plus you can often reuse the studs.
a quick little technique to find high and low spots if you didnt know is sanding the area. its easy to ID the high and low spots. high spots will not allow the sand paper to sand around it, low spots wont allow the sand paper to sand in it.
Most dent consist of a low and a high area. The high area may or may not be very noticable. If you thing of throwing a rock into a lake, you notive that it causes the dip where the rock went in, but also it will cause a wave (high) area. Metal acts the same way. When it is pushed in in one area, it forces the metal have highs (waves) in other areas. Your direct damage is the low pint of impact and the high is your secondary damage. It take a little more focus to locate the secondary damage
also i think it is a little more precise than a slide hammer for hard to get areas or for small dents that dont need much. you dont wanna slide hammer to hard or you will create a high spot which makes more work.
April 2nd, 2010 at 9:32 pm
It is just a T-puller. It just uses the force from the pull that you put on it. It helps eliminate popping or forcing the metal.
April 3rd, 2010 at 12:20 am
What you mean by high area? the t pull is to pull the dent out right? is the high area visible which is why you are hammering it. High are an in a bump facing outward of the damage area?
April 3rd, 2010 at 12:34 am
A common mistake is to just work on the direct (low) damage and not the high areas. It is important to work on both areas at the same time. You want to push in on your highs as you pull out on your lows. This will allow the metal to return to it’s origional shape with out forcing or streching the metal.
April 3rd, 2010 at 12:54 am
i do prefer to pull the trigger on the spot welder for only about 1/2 second. the studs to pop off every now and then, but this helps when pulling them off. just a little jiggle and they are off “no hole no grinding no cutting”. plus you can often reuse the studs.
April 3rd, 2010 at 2:49 am
a quick little technique to find high and low spots if you didnt know is sanding the area. its easy to ID the high and low spots. high spots will not allow the sand paper to sand around it, low spots wont allow the sand paper to sand in it.
April 3rd, 2010 at 3:57 am
Most dent consist of a low and a high area. The high area may or may not be very noticable. If you thing of throwing a rock into a lake, you notive that it causes the dip where the rock went in, but also it will cause a wave (high) area. Metal acts the same way. When it is pushed in in one area, it forces the metal have highs (waves) in other areas. Your direct damage is the low pint of impact and the high is your secondary damage. It take a little more focus to locate the secondary damage
April 3rd, 2010 at 5:46 am
pdr wasnt the topic of the tutorial, and not what was being taught in the vid
April 3rd, 2010 at 6:19 am
What tool is that he is using? the thing he is substituting for a puller. The cork screw looking thingy.
April 3rd, 2010 at 6:24 am
also i think it is a little more precise than a slide hammer for hard to get areas or for small dents that dont need much. you dont wanna slide hammer to hard or you will create a high spot which makes more work.
April 3rd, 2010 at 7:32 am
paintless dent repair could have done the job